FPA830

Lightweight, adjustable Miller Shadow Beam Anchor I, H,& W from 4 in to 12 in (10 cm to 30 cm).

$337.95

Return conditions : No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page.

Removable anchoring device for horizontal beam type I , H , and W , for quantities of from 4 to 12 inches (10 cm to 30 cm).

According to manufacturer , the removable anchor beam is designed to withstand static forces of 5000 pounds (22.2 KN). This, according to the testing standards established by ANSI Z359.1 -2007 standard.

The maximum weight of the worker ( including clothing , tools, etc. . ) Can use this vertically movable anchor is 310 lb ( 140.6 kg). According to a technical review of Miller (see attached PDF instruction manual ) . When the anchor is in the horizontal position, the worker must select retractable lanyards or a model along with two energy absorbing devices.

It is important to remember that this anchor should never be installed too close to the end of the beam. That this device is not designed for use on a vertical surface . Or indeed on a beam with more than 15 ˚ to the horizontal. In summary this anchorage must be used on a horizontal surface.

The worker is responsible for conducting a routine inspection before each use. During this routine inspection, the worker must observe any signs of deterioration , wear, malfunction or breakage. You must replace your removable anchor beam at the slightest sign of failure mentioned above.

In addition, the removable anchor beam should be inspected by a qualified person other than the worker who uses the equipment. We should not forget that the more work and environmental conditions are difficult, the more often you should inspect the movable anchor .

Sylprotec offers an inspection service fall protection . You can learn more by looking under the Service tab Sylprotec logo at the top of the page.

All equipment is subject to a fall or impact must be decommissioned.

For cleaning, use mild soap and clean warm water (37 ° C). Do not use bleach or other abrasives or chemicals. Be sure to clean the holes in the support arm ratchet button and release arm with a stiff broom or compressed air.

Dry with compressed air without any excessive heat . You can help yourself by wiping with a clean cloth very absorbent .

Type of product Safety equipment
Main category Personal protection
Sub category Fall protection
Sub sub category Anchorage & connectors
Name of the product Removable anchoring device
Product code FPA830
Approved/Certified Complies with ANSI Z359.1-2007.
Manufacturer Miller
Features The anchor point is horizontal, the worker must select retractable lanyards or a lanyard model with 2 energy absorption devices
Additional Features This device is not designed to be used on a vertical surface. Nor, for that matter, on a beam having more than 15˚ with the horizontal
Format 4 à 12 in (10 cm à 30 cm).
Comfort features Capable of withstanding a force of 5000 lbs (22 kN) without deforming
Washable Wash in warm water, 98.60°F/ 37°C. Never use bleach or other abrasive or chemical products on your harness. Air dry
Height (in/cm) 3.25 in / 8.25 cm
Length (in/cm) 22 in / 55.88 cm
Width (in/cm) 8.5 in / 21.6 cm
Weight (lb/kg) 7.6 lbs / 3.5 Kg
Sold by Unit
Caution The maximum weight supported is 310 lbs (141 kg), which includes the weight of tools and any other equipment carried by the worker
Return conditions No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page.

Reviews

No customer reviews for the moment.

Write a review
Lightweight, adjustable Miller Shadow Beam Anchor  I, H,& W from 4 in to 12 in (10 cm to 30 cm).

Lightweight, adjustable Miller Shadow Beam Anchor I, H,& W from 4 in to 12 in (10 cm to 30 cm).

Accessories

18 other products in the same category: