FPH2000AL

Peakworks contractor safety harness, 1 back and 1 front D-rings, mating buckles class A and L

$136.65

Return conditions : No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page

Peakworks safety harness. CSA groups A and L, with one back D-ring and one front D-ring. The chest and leg straps close with mating buckles. Universal size. This safety harness is equipped with two steel D-rings: one in the back and one in the front.

Peakworks product code: V8002020 or model FBH-10000L.
Complies with ANSI Z359.1 and CSA Z259.10-12.

This harness can support a maximum weight of 400 lb (180 kg), including clothing, tools, etc.

This Peakworks safety harness is made of woven non-stretch polyester. Polyester offers a superior resistance to acids. The front straps at the chest level (also called the Bavarian) are equipped with a small D-ring that allows the connection of the harness with a ladder. The chest straps and leg straps close with mating buckles. The product identification and certification labels are sewn onto the strap on the back left side of the safety harness.

Inspection:

The worker is responsible for visually inspecting the harness before each use. During this routine inspection, the worker must note any signs of degradation, malfunction, or breakage. The harness will have to be replaced if any such signs are detected.

On top of this routine inspection, the harness must be inspected by a qualified person different than the worker that wears the harness. The frequency of these inspections varies according to the manufacturer. Some manufacturers require an inspection every 90 days, others every 180 days, or even yearly. These inspections should be performed more often if the harness is worn in extreme environmental working conditions.

The recommended lifetime of a safety harness if 5 years. While some manufacturers keep silent on this topic, in practice, if the harness is used regularly and stored and maintained in standard conditions, its lifetime will not exceed 5 years in most cases.

Sylprotec offers a safety harness inspection service. Find out more by clicking on the Services tab, under the Sylprotec logo at the top of the page.

Any equipment that has withstood a fall or an impact must be scrapped.

Maintenance:

For cleaning, use a gentle soap or detergent and lukewarm water (37°C). Do not use bleach, chlorine, or other abrasive or chemical products. If your harness is too dirty or contaminated, it is time to replace it.

Air dry without using heat, in a clean environment. You can accelerate the drying process by wiping the wet harness with a clean absorbent wipe, or by using a fan. Avoid exposing the harness to sunlight and to any sources of contamination.

Suggestion:

To complete your fall protection you will find a range of lanyardsretractable and anchors. Some products are suggested under the "accessories" tab at the bottom of this page.

Other equipment frequently used with this safety harness:

Safety glasses YA12E93101DX
Liberty TA14LR safety helmet and the essential TA14CS chin strap
EPTCONE28 Traffic Cones
Peakworks FPBAG storage bag
The FPL9900 Tool Strap

The texts coloured in green correspond to hyperlinks leading to specific safety equipment or to a general information link.

Type of productSafety equipment
Main categoryPersonal protection
Sub categoryFall protection
Sub sub categoryFall protection safety harness
Name of the productSafety harness
Series of productsContractor
Product codeFPH2000AL
Approved/CertifiedMeets the standards ANSI Z359.11-2014 and CSA Z259.10-12
ManufacturerPeakworks
Country of originChina
Choice of formatUniversal sizes (medium to extra-large)
ReusableReusable with careful inspection and proper installation
FeaturesThe chest and leg straps are joined by interlocking buckles
Additional FeaturesThis harness has 5 adjustment points: 2 on the legs, 2 on the torso and 1 on the chest
Characteristic adding safetyThis harness is equipped with a sub-pelvic strap
Characteristics of metal partsNon-painted metal parts
IncludesWith a dorsal and frontal ring.
Includes 3The ends of the straps have plastic tips to prevent fraying and allow the user to adjust the harness easily even when wearing work gloves
Property of the materialPolyester straps offer better resistance to acidic chemicals
ClassificationClass A, L
Feature that facilitates useThe straps have distinct colors for easy donning
Material1Polyester
Material2Steel
WashableWash in warm water, 98.60°F/ 37°C. Never use bleach or other abrasive or chemical products on your harness. Air dry
Length (in/cm)11 in / 27.94 cm
Width (in/cm)11 in / 27.94 cm
Height (in/cm)2 in / 5.08 cm
Weight (lb/kg)4.2 lb / 1.91 Kg
Sold byUnit
ColorHigh Visibility Green/Black/Grey
Another packaging available5 units per box
Return conditionsNo returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page
CautionThe maximum weight of the worker that can wear this harness is 400 lb / 181.4 kg, including clothing, tools, etc.

Accessories

23 other products in the same category: