Sale! Peakworks extendable Y-lanyard with an energy absorbing inner core and a strong polyester tubular webbing. View larger


E4 Peakworks extendable Y-lanyard with an energy absorbing inner core and a strong polyester tubular webbing.




Return conditions : No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page


Peakworks "Y " polyester web lanyard featuring two energy absorbing inner core and a strong protective outer shell made of polyester tubular webbing. Width: 1 in, Length: 6 ft. (25 mm X 1.83 m). This lanyard features a dual leg which allows the worker to remain connected to a safety system when passing intermediate anchor points. This lanyard is equipped with three identical standard double locking carabiners with a ¾ in (19 mm) throat opening.

This E4 lanyard can support a weight of 99 lbs to 253 lbs (44.91 kg to 114.76 kg), including clothing, tools and equipment.

This lanyard is available in lengths of four (4').

The energy absorber is designed to reduce the impact of a fall below a force of 900 pounds (4kN). During a fall, the energy absorber deploys over a distance of 48 in. (4 ft) to reduce the fall arrest force upon the worker. Once deployed, lanyards and harnesses must be replaced. Think of it as a narrow escape.

This product conforms to CSA Z259.11-05.

It features three identical carabiners (hooks) made of steel that require a double-locking action for a throat opening of a ¾ in. Meets the standard ANSI Z359.1-2007 SO therefore, can support a force of 3600 lb (16kN) without any distortion. The nearest carabiner to the energy absorber must be hooked to the dorsal anchorage point on the harness.

Certification labels provided at one end of the lanyard.

Once the worker is positioned to work, he must attach himself with a single strap and the other leg must be hooked to the front of the harness. The anchor point should be located above the dorsal anchorage ring and should be held in a vertical position with respect to the worker. One should also be aware of the potential risk of falling. Is there a sufficient and obstacle free distance below the worker? Are there emergency measures to get him down on the ground quickly? Can the anchor point withstand a force of 5000 lb? For more information, consult the manufacturer's manual.

The worker is responsible for visually inspecting the lanyard before each use. During this routine inspection, the worker must note any signs of degradation, malfunction, or breakage. The lanyard will have to be replaced if any such signs are detected.

On top of this routine inspection, the lanyard must be inspected by a qualified person different than the worker. The frequency of these inspections varies according to the manufacturer. Some manufacturers require an inspection every 90 days, others every 180 days, or even yearly. These inspections should be performed more often if the lanyard is worn in extreme environmental working conditions.

The recommended lifetime of a lanyard is 5 years. While some manufacturers keep silent on this topic, in practice, if the lanyard is used regularly and stored and maintained in standard conditions, its lifetime will not exceed 5 years in most cases.

Sylprotec offers a lanyard inspection service. Find out more by clicking on the Services tab, under the Sylprotec logo at the top of the page.

Any equipment that has withstood a fall or an impact must be scrapped.

For cleaning, use a gentle soap or detergent and lukewarm water (37°C). Do not use bleach, chlorine, or other abrasive or chemical products. If your harness is too dirty or contaminated, it is time to replace it.

Air dry without using heat in a clean environment. You can accelerate the drying process by wiping the wet lanyard with a clean absorbent wipe, or by using a fan. Avoid exposure to sunlight and to any sources of contamination.

Type of productSafety equipment
Main categoryPersonal protection
Sub categoryFall protection
Sub sub categoryLanyards
Name of the productTubular lanyard
Product codeFPL2000
Approved/CertifiedComplies with ANSI Z359.1-2007
Country of originChina
Choice of formatLength of 4 or 6 ft / 1.22 or 1.83 m
ReusableReusable with careful inspection and proper installation
FeaturesThe energy absorber is designed to reduce the impact force of the fall below 900 lb (4 kN)
Characteristic adding safetyThe carabiners are capable of withstanding a force of 3600 lb (16 kN) without deforming
IncludesWith internal shock cord. Width: 1" (25 mm)
Includes 2Equipped with tree standard carabiners with a ¾" / 19 mm opening. They are self-locking and require a double action to open
ClassificationType E4
Worker’s weight99 to 253 lb/ 44.91 to 114.76 Kg
WashableWash in warm water, 98.60°F/ 37°C. Never use bleach or other abrasive or chemical products on your lanyard. Air dry
Height (in/cm)Variable according to selection
Length (in/cm)Variable according to selection
Width (in/cm)Variable according to selection
Weight (lb/kg)Variable according to selection
Sold byUnit
Dimensions of the productThe dimensions of the product depend on the size selected by the customer.
CautionMaximum supported worker weight of 99 lb to 253 lb / 44.91 kg to 114.76 kg, including clothing, tools and equipment
Return conditionsNo returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page

11 other products in the same category: