New Peakworks Y-lanyard with an energy absorbing inner core and a strong polyester webbing, 200-350 lb. View larger

Peakworks Y-lanyard with an energy absorbing inner core and a strong polyester webbing, 200-350 lb.

$167.85

Please select the available option below :

Return conditions : No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page.

Peakwork "Y " polyester web lanyard featuring two energy absorbing inner core and a strong protective outer shell made of polyester webbing. Width: 1 in, Length: 6 ft. (25 mm X 1.83 m). This lanyard features a dual leg which allows the worker to remain connected to a safety system when passing intermediate anchor points. This lanyard is equipped with three identical standard double locking carabiners with a ¾ in (19 mm) throat opening.

This lanyard can support a weight of 200 lbs to 350 lbs (90 kg to 159 kg), including clothing, tools and equipment.

The energy absorber is designed to reduce the impact of a fall below a force of 900 pounds (4kN). During a fall, the energy absorber deploys over a distance of 48 in. (4 ft) to reduce the fall arrest force upon the worker. Once deployed, lanyards and harnesses must be replaced. Think of it as a narrow escape.

This product conforms to CSA Z259.11-05.

It features three identical carabiners (hooks) made of steel that require a double-locking action for a throat opening of a ¾ in. Meets the standard ANSI Z359.1-2007 SO therefore, can support a force of 3600 lbs (16kN) without any distortion. The nearest carabiner to the energy absorber must be hooked to the dorsal anchorage point on the harness.

Certification labels provided at one end of the lanyard.

Once the worker is positioned to work, he must attach himself with a single strap and the other leg must be hooked to the front of the harness. The anchor point should be located above the dorsal anchorage ring and should be held in a vertical position with respect to the worker. One should also be aware of the potential risk of falling. Is there a sufficient and obstacle free distance below the worker? Are there emergency measures to get him down on the ground quickly? Can the anchor point withstand a force of 5000 lbs? For more information, consult the manufacturer's manual.

The worker is responsible for visually inspecting the lanyard before each use. During this routine inspection, the worker must note any signs of degradation, malfunction, or breakage. The lanyard will have to be replaced if any such signs are detected.

On top of this routine inspection, the lanyard must be inspected by a qualified person different than the worker. The frequency of these inspections varies according to the manufacturer. Some manufacturers require an inspection every 90 days, others every 180 days, or even yearly. These inspections should be performed more often if the lanyard is worn in extreme environmental working conditions.

The recommended lifetime of a lanyard is 5 years. While some manufacturers keep silent on this topic, in practice, if the lanyard is used regularly and stored and maintained in standard conditions, its lifetime will not exceed 5 years in most cases.

Sylprotec offers a lanyard inspection service. Find out more by clicking on the Services tab, under the Sylprotec logo at the top of the page.

Any equipment that has withstood a fall or an impact must be scrapped.

For cleaning, use a gentle soap or detergent and lukewarm water (37°C). Do not use bleach, chlorine, or other abrasive or chemical products. If your harness is too dirty or contaminated, it is time to replace it.

Air dry without using heat in a clean environment. You can accelerate the drying process by wiping the wet lanyard with a clean absorbent wipe, or by using a fan. Avoid exposure to sunlight and to any sources of contamination.

Type of product Safety equipment
Main category Personal protection
Sub category Fall protection
Sub sub category Lanyards
Name of the product Lanyard
Product code FPL64022
Approved/Certified Complies with ANSI Z359.1-2007.
Manufacturer Peakworks Inc
Features It has two identical straps that allow the worker to remain attached while moving from one anchor point to another.
Additional Features The energy absorber is designed to reduce the impact force of the fall below 900 lbs (4kN).
Comfort features The carabiners are capable of withstanding a force of 3600 lbs (16kN) without deforming.
Washable Wash in warm water, 98.60°F/ 37°C. Never use bleach or other abrasive or chemical products on your harness. Air dry
Height (in/cm) 2 in / 5.08 cm
Length (in/cm) 13 in / 33 cm
Width (in/cm) 6 in / 15.24 cm
Weight (lb/kg) 5 lbs / 2.26 Kg
Color Vert haute visibilité / Black
Sold by Unit
Return conditions No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page.

Reviews

No customer reviews for the moment.

Write a review
Peakworks Y-lanyard with an energy absorbing inner core and a strong polyester webbing, 200-350 lb.

Peakworks Y-lanyard with an energy absorbing inner core and a strong polyester webbing, 200-350 lb.

13 other products in the same category: