Open-finger glove with Dyneema® cut level A2, polyurethane palm-coated. Sold in pairs.

Dexterity® A2 Dyneema® cut-resistant glove with three open fingers

This Dexterity® cut-resistant glove made with Dyneema® knit is designed for work where hand protection still has to leave excellent fingertip feel. Its three open fingers help with small parts, tools, screws, keyboards and fine components, while the polyurethane coating improves grip on dry or slightly slippery surfaces. It is a useful choice when dexterity is the priority, with the important limitation that the open fingertips do not replace a fully closed glove when the cut hazard is directly at the fingertips.

The Superior product code is SSXPU3OF. This glove is sold by the pair and is available from extra small (6) to extra large (10). Please select the required size in the field above before adding it to the cart.

ANSI A2 protection in a Dexterity® Dyneema® open-finger glove

According to the ASTM and ANSI ratings shown for this item, this model provides A2 cut resistance and level 3 puncture resistance. The Dyneema® knit helps keep the glove light and flexible, while the grey polyurethane coating helps maintain controlled grip during precision work.

The three open-finger design is especially useful when the worker has to feel small parts, operate controls, handle fasteners or keep fine movement. This design improves precision, but it leaves the fingertips exposed, so it should be used only where that limitation fits the actual job hazard.

Applications for the A2 cut-resistant glove in construction and assembly

This glove is recommended for general construction, carpentry and woodworking, heavy equipment operation, heating, ventilation and air-conditioning maintenance, plumbing, automotive work, metalworking, metal fabrication, small-parts assembly, electronics, pulp and paper operations and plastic production.

It fits naturally within the cut-resistant gloves category when the job requires a balance between protection, grip and direct tactile feel.

Dyneema® knit and polyurethane coating for precision grip

The Dyneema® knit helps keep the glove light and supple. The polyurethane coating on the grip area adds a tacky surface without making the glove bulky, which is useful for holding smooth parts, components, hand tools or thin materials. The white and grey colour gives a clean professional look while making contamination easier to notice during inspection.

Care for the Dexterity® Dyneema® polyurethane-coated glove

To help extend service life, perform basic care. The original text recommends washing in cold water, 85°F / 30°C, with a mild detergent, followed by a cold-water rinse. The glove may then be tumble dried at low temperature. Do not use bleach on this glove.

Always inspect the knit, coating, seams and finger openings before reuse. Replace the glove if the coating is worn, if the knit is cut or if the protection no longer properly covers the hand.

Restrictions for this A2 cut-resistant glove with three open fingers

This glove does not protect the open fingertips. It is not designed for immersion in liquids, chemical protection, high heat, flame exposure or severe cut hazards that require a higher protection level. Like any protective glove, it reduces certain risks without eliminating them completely; the model must always match the real hazard at the workstation.

FAQ about the Dexterity® A2 cut-resistant open-finger glove

What are the three open fingers used for?

They help maintain better tactile feel for small parts, screws, fasteners, controls and precision tools.

What cut-resistance level does this model provide?

The item page lists ASTM/ANSI A2 cut resistance and level 3 puncture resistance.

Does this glove protect the fingertips?

No. The three open fingers leave the fingertips exposed. Choose a closed glove when the hazard is directly at the fingertips.

What sizes are available for this glove?

It is available from extra small (6) to extra large (10), according to the variants available on the item page.

How should this Dyneema® and polyurethane glove be cared for?

Wash it in cold water with a mild detergent, rinse it in cold water and dry it at low temperature. Avoid bleach according to the care text on the item page.

Complementary suggestions for cut-resistant gloves and safety equipment

To complete your safety equipment, see the 18-gauge touchscreen-friendly version (GS18KGFN), the TenActiv™ cut-resistant ANSI A7 glove (GSTACXPNRT), the A9 stainless steel chain mail cut-resistant glove (G100), the TenActiv™ cut-resistant ASTM/ANSI A9 glove (GS21TXUFN), the TenActiv™ cut-resistant ASTM/ANSI A4 glove (GSTAFGFNT) and the A4 cut-resistant winter glove with waterproof membrane (GS18WTFN). Under "Accessories" at the bottom of the page, complete with the Chemstop cotton knit glove coated with nitrile (GNTFC) and the Sentec safety eyewear with clear polycarbonate lenses (YA12E90801).

Green text corresponds to links toward our selection of cut-resistant gloves and compatible safety accessories.