3M 6000 series NIOSH 42 CFR 84 approved full facepiece respirator for respiratory protection. Compatible with 3M filters series 2000, 2200, 5000 and 7000; 3M cartridges series 6000; and P100 cartridge/filters. Filters and cartridges sold separately. This code is for the large size full facepiece respirator. Sold individually. 4 unit/case.
This full facepiece is made of thermoplastic elastomer (TPE) but the faceseal is made of silicone. The head harness is equipped with four ajustable head straps. None of the components contain natural rubber latex. Fullface respirators are particularly usefull when one must protect himself from vapours that may cause skin and eye irritation. The lens made of polycarbonate which is approved for impacts on this full facepiece may be use as safety eyewear.
This type of respiratory protection is recommended for work that will loosen solid or liquid particles in the air and/or for work in an environment where air contains contaminants and/or biological particles. One must of course adapt its filtering system with the right filters or cartridges to be properly protected.
Do not use for:
Do not use on a beard and other facial hair or if the user suffers from a condition that prevents him from having direct contact with the respirator’s sides. The use of respirators is not recommended for people with compromised respiratory system or problem such as asthma or emphysema.
It is strongly discouraged to wear a respirator for application with sandblasting. It is also highly advised to stay away from environment that exceed 10 times the permissible exposure limit set by the CNESST or any other government regulation applicable.
To get a protection from concentrations up to 50 times the exposure limit, it is crucial that one succeeds a quantitative fit test given by the manufacturer.
One should never use a respirator in an oxygen deprevated environment (an atmosphere with less than 19,5 % oxygen).
Maintenance and service life:
3M full facepiece respirators 6000 series are reusable, provided that its maintenance and storage is done according to the manufacturer’s rules. 3M recommends an inspection of the respiratory equipment before each use; to wash the respirator after each use; and to store the respirator back to its packaging. One should never wash its respirator with any type of solvents since they can weaken some components which can affect the efficiency of the equipment. One must always remove the cartridges or filters from the respirator before storing it.
Other sizes are available in the menu below this page.
|Type of product
|Sub sub category
|3M respirators and cartridges
|Name of the product
|Full face respirator
|Series of products
|6000 series respirator
|Country of origin
|United State of America
|Choice of format
|Small, medium , large
|Reusable with prior hygienic measurement
|Type of connection
|Bayonet type connector
|FPC=10 with qualitative adjustment tests, FPC=50 with quantitative adjustment tests
|With silicone face seal
|Cartridge or Filter Included
|Filter element not Include
|Includes natural rubber latex components
|Does not contain latex
|Contains a Cool flow valve (Tm) 3M (Tm)
|Compatibility with the mask screen used for welding
|Not compatible with the mask screen used for welding
|Contains two inhalation valves
|High impact polycarbonate (meets ANSI Z87.1)
|Without phonic membrane
|Type of harness
|4 attachment points
|Wash in warm water, 140°F/60°C with a mild soap (hand dish soap), rinse and disinfect with a Dakin solution (water with bleach), rinse thoroughly and let dry
|10 in / 25.4 cm
|8.25 in / 20.95 cm
|6 in / 15.2 cm
|1.46 lb / 0.66 Kg
|Another packaging available1
|4 units per case
|Another packaging available2
|36 cases per pallet (144 units)
|No returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page