compare_arrows

Striped photoluminescent tape, black, 30 ft

Reference : ECTNOPH-2
$97.90

This item is not kept in stock. Please allow 5 days for delivery.

Tape with black and photoluminescent stripes to mark off hazard areas and mark steps, handrails and exit routes, available in 30 ft rolls in a 2, 4 or 6 in width. It recharges with ambient light, with no electricity, and the manufacturer states 6 hours or more of glow. Its permanent pressure-sensitive adhesive holds on clean, dry indoor surfaces.

Width: 2 in
Quantity

Compare

Striped photoluminescent tape, black, 30 ft

This item is not kept in stock. Please allow 5 days for delivery.

Available widths: 2 in, 4 in and 6 in, 30 ft roll

Available in 3 widths. Select the variant you need from the drop-down menu.

Sylprotec codeWidthLengthWeight
ECTNOPH-22 in (5.08 cm)30 ft (9.14 m)0.5 lb (0.23 kg)
ECTNOPH-44 in (10.16 cm)30 ft (9.14 m)1 lb (0.45 kg)
ECTNOPH-66 in (15.24 cm)30 ft (9.14 m)1.5 lb (0.68 kg)

The dimensions shown are for variant ECTNOPH-2.

This tape with black and photoluminescent stripes marks off hazard areas and critical spots when the lighting fails: step edges, handrails, door frames, exit routes and the surroundings of safety equipment. The black bands keep the contrast by day and in dim light. Its photoluminescent bands absorb ambient light during normal lighting hours, then release it as a glow in the dark, with no electricity: the manufacturer states 6 hours or more of luminance. Its permanent pressure-sensitive adhesive holds on clean, dry indoor surfaces. It complements emergency lighting and exit signage, without replacing them. The 30 ft (9.14 m) roll comes in a 2 in (5.08 cm), 4 in (10.16 cm) or 6 in (15.24 cm) width. It is made in the United States.

Features of the striped photoluminescent tape

  • Coloured stripes alternating with photoluminescent bands to mark hazards.
  • Recharges with ambient light and glows for 6 hours or more in the dark.
  • Works with no electricity or battery.
  • Permanent pressure-sensitive adhesive for a lasting application.
  • Three widths, from steps and handrails to walls and large areas.

Striped photoluminescent tape applications

The manufacturer recommends it for hazard striping, emergency exit routes and stairwells, marking handrails, door frames and safety equipment, and evacuation markers in the event of a total lighting failure. The 2 in width suits steps and handrails, the 4 in width stays clearly visible on walls and around hazard areas, and the 6 in width, the most visible, suits walls and large areas. Important: check with local, provincial and federal authorities that this product is suitable for your use in an evacuation route or emergency exit. This page carries black stripes only. The same widths come in red stripes on the sister page, the striped photoluminescent roll (ECTRGPH), red, 30 ft. For a continuous, fully photoluminescent marker, choose the plain photoluminescent tape (ECTPH), 30 ft instead, a separate construction.

Striped photoluminescent tape technical specifications

FeatureDetail
ColourBlack stripes alternating with photoluminescent bands
TypeStriped photoluminescent tape
MaterialVinyl
Luminance6 hours or more in the dark after charging with ambient light
Widths2 in (5.08 cm), 4 in (10.16 cm) or 6 in (15.24 cm)
Length30 ft (9.14 m) per roll
AdhesivePermanent, pressure-sensitive
Application surfaceClean and dry, indoors
Standards cited by the manufacturer and its distributorsDIN 67510, ASTM E2072-14, ISO 15370, EU Marine Equipment Directive, IMO Resolution A.752(18), PSPA Class B
Country of originUnited States
Sold byRoll

Photoluminescent tape installation and care

Clean the surface and let it dry: the permanent adhesive requires a clean, dry substrate. Unroll the tape, cut it to length and press it firmly across its full width. Apply it where it receives ambient light during normal lighting hours, since that light recharges it. Keep its surface clean so it keeps charging and glowing, and replace any damaged section.

FAQ: striped photoluminescent tape

Which width should I choose?

The 2 in suits steps and handrails. The 4 in stays clearly visible on walls and around hazard areas. The 6 in, the most visible, suits walls and large areas.

How long does it glow in the dark?

The manufacturer states a visible glow for 6 hours or more in the dark, after charging with ambient light.

What is the difference with the plain photoluminescent tape?

The plain tape is fully photoluminescent and lays out a continuous marker; the striped tape alternates photoluminescent bands and coloured bands to signal a hazard. They are two separate constructions: the standards cited for the plain version are not certifications of this striped tape.

Does it replace emergency lighting?

No. It complements emergency lighting and exit signage by marking hazards and routes. Check with local, provincial and federal authorities that the product is suitable for each use in an evacuation route or emergency exit.

Can it be used outdoors?

The manufacturer presents it as an indoor marking solution. Apply it to clean, dry indoor surfaces.

Suggestions for the striped photoluminescent tape

For the technician who applies the stripes to the steps of a service stairway, plan for the Impacto (VG104) soft rubber knee pads with foam, the TenActiv (GS21TXUGFN) high-visibility ultra-thin cut-resistant gloves, the 3M (YASF401BG) SecureFit 400 series safety glasses with clear anti-fog lens, the MSA V-Gard (TA83-W) matte white helmet, type 1 class E and the 3M 1100 (O1100) uncorded disposable earplugs.

To complement your equipment: Photoluminescent Running Man exit sign with 90 degree right arrow (EI313PH); Photoluminescent Running Man exit sign with down arrow (EI309PH) and Green Running Man LED emergency exit sign, thermoplastic casing, with back-up battery (LUMR).

The texts coloured in green correspond to hyperlinks leading to specific safety equipment or to a general information link.

ECTNOPH-2

Data sheet

Product group
Safety equipment
Main category
Sign and lock
Sub category
Cones and barricade tapes
Name of the product
Photoluminescent tape
Product code
ECTNOPH
Sort by keywords
Marking tapes
Product use
Photoluminescent marking
Approved/Certified
DIN 67510 ; ASTM E2072-14 ; ISO 15370 ; EU Marine Equipment Directive ; IMO Resolution A.752(18) ; PSPA Class B
Manufacturer
Incom Direct
Country of origin
United States of America
Choice of format
2, 4 and 6 in
Features
To mark exits, stairs and handrails in the dark
Additional Features
Charges from ambient light
Characteristic adding safety
Photoluminescent: charges from ambient light, then glows in darkness.
Mounting type
Permanent adhesive back
Material
Vinyl
Length (ft/m)
30 ft / 9.14 m
Dimensions of the product
360 x 2 in / 914.4 x 5.08 cm
Length (in/cm)
4.3 in / 10.922 cm
Width (in/cm)
4.3 in / 10.92 cm
Height (in/cm)
2 in / 5.08 cm
Weight (lb/kg)
0.501 lb / 0.227 kg
Availability
Allow 5 days for delivery
Sold by
Roll
Color
Black/Photoluminescent
HS Code
3920690000
Return conditions
Not returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page
Caution
For indoor use

Specific References

MPN
GT230BK

You might also like

Comments (0)
No customer reviews for the moment.