- New
Laminated PVC hazard tape, yellow/black, 108 ft, 1 to 6 in
ECT751JN108-4
$50.25
Laminated yellow and black hazard tape sold in a 108 ft roll, for continuous marking of traffic lanes and long workshop or warehouse runs, and for marking physical hazards on floors, walls, pipes and equipment. Choose a width of 1, 2, 3, 4 or 6 in from the menu; the length stays fixed. Made of 6.3 mils soft PVC under a clear protective film, it has a smooth gloss finish and a pressure-sensitive rubber-based adhesive.
Return conditions:
No returnable if used. For more information about our return policy, please refer to the Orders and Returns.
Laminated PVC hazard tape, yellow/black, 108 ft, 1 to 6 in
One 108 ft length, five widths to suit the lane, wall or equipment you need to mark.
Available in 5 widths. Select the width you need from the drop-down menu.
| Format | Sylprotec code | Best used for |
|---|---|---|
| 1 in X 108 ft | ECT751JN108-1 | Color coding and identification on pipes and equipment |
| 2 in X 108 ft | ECT751JN108-2 | Discreet marking lines and bundling |
| 3 in X 108 ft | ECT751JN108-3 | Bands on walls and around equipment |
| 4 in X 108 ft | ECT751JN108-4 | Continuous marking of workshop lanes |
| 6 in X 108 ft | ECT751JN108-6 | Widest band for long warehouse runs |
This yellow and black tape marks physical hazards and creates visible markers on floors, walls, pipes and equipment. Its 108 ft roll suits continuous marking, when a workshop lane or warehouse run calls for a band with few joints. The 6.3 mils soft PVC is covered with a clear protective film and applied with a pressure-sensitive rubber-based adhesive. According to the manufacturer, its colors follow the ANSI Z535.1 color code.
Features of the 108 ft laminated hazard tape
- 108 ft roll for continuous marking.
- Five widths available: 1, 2, 3, 4 and 6 in.
- Soft PVC under a clear protective film.
- Abrasion resistance.
- Smooth gloss finish, easily cleaned.
- Pressure-sensitive rubber-based adhesive.
Applications of the 108 ft laminated hazard tape
The manufacturer intends this series for industrial identification, color coding, lane marking and bundling. The 108 ft length comes into its own on a workshop lane, along a warehouse aisle or around a group of equipment, where the marking continues over several sections. Yellow and black draw attention to a physical hazard such as a pillar, an edge or a low pipe.
Choose the width according to the surface to mark and the viewing distance you want. The 1 in and 2 in widths suit pipes, color coding and discreet lines; the 3 in and 4 in widths give a stronger band on a wall or along a lane; the 6 in is the widest band on this page, for a long warehouse run. This laminated tape remains smooth: where foot traction is the concern, choose an anti-slip tape instead.
Technical specifications of the 108 ft laminated hazard tape
| Characteristic | Detail |
|---|---|
| Material | Soft PVC |
| Protective film | Clear |
| Adhesive | Rubber-based, pressure-sensitive |
| Finish | Smooth gloss, easily cleaned |
| Color | Yellow/Black |
| Tape thickness | 6.3 mils (0.160 mm) |
| Roll dimensions | For the 4 in X 108 ft roll: height 4 in / 10.16 cm (tape width), approximate diameter 5 in / 12.7 cm, roll laid flat |
| Weight | For the 4 in X 108 ft roll: 1.68 lb / 0.762 kg |
| Service temperature | Below 60 °C / 140 °F |
| Adhesion to steel (typical value) | 0.20 kg/cm; 17.64 oz/in |
| Elongation at break (typical value) | 180 % |
| Tensile strength (typical value) | 3.1 kg/cm; 17.6 lb/in, values as published |
| Storage | One year from dispatch, at moderate temperature and humidity |
| Country of origin | Taiwan |
| Sold by | Roll |
Typical values are averages measured by the ASTM D-1000 test method. They are a general guide and do not indicate any allowable load.
Care and application of the 108 ft laminated hazard tape
On a long run, prepare the full length of the path before unrolling the tape: the surface must be clean, dry and smooth, free of contaminants. Test the tape on the surface, then press it firmly into place. The smooth finish is easily cleaned. Respect the published service limit, below 60 °C / 140 °F, and store unused rolls at moderate temperature and humidity.
FAQ: the 108 ft laminated hazard tape
What is the clear protective film for?
It covers the yellow and black PVC and gives the tape its smooth gloss finish, which is easily cleaned. The manufacturer also states abrasion resistance for this series.
Which width should I choose for a long run?
The 4 in suits continuous marking along a workshop lane, and the 6 in gives the widest band on this page. For pipes or color coding, choose the 1 in or 2 in instead. The length remains 108 ft in every case.
Which surfaces can this tape be applied to?
The manufacturer mentions floors, walls, pipes and equipment. The surface must be clean, dry and smooth; a test on your surface confirms adhesion before you mark the whole run.
What are the limits of use for this tape?
It is used below 60 °C / 140 °F. The ANSI Z535.1 color code is stated by the manufacturer; it is not an approval by an independent body.
What are the dimensions of the 4 in X 108 ft roll?
Laid flat, this roll is 4 in high, which is the tape width, with an approximate diameter of 5 in. It weighs 1.68 lb / 0.762 kg. The other widths have their own dimensions.
Suggestions for the 108 ft laminated hazard tape
For the person applying this tape along a long workshop run, plan on the skid-proof, non-marking Impacto kneepads (VG102), the 3M SecureFit protective eyewear (YASF401), the TenActiv ASTM/ANSI level A3 cut-resistant foam nitrile gloves (GS13TAFNT) for cutting, according to your risk assessment, and the high-visibility orange safety vest (VV50) to stay visible in aisles used by lift trucks. If the area requires head protection, add the Delta Plus Independence safety helmet (TA14LR).
To cut and cordon off while marking, add the safety knife (SAEC5) with automatic retractable blade and its plastic swivel sheath (SAEEC5). The expandable safety barricade (EPT195) in yellow polypropylene and the bilingual yellow CAUTION DO NOT ENTER barricade tape (ECT3YB1) temporarily mark off the work area. Where lift trucks operate, complete the marking with the round CAUTION FORKLIFT TRAFFIC anti-skid vinyl floor sign (EDCH).
ECT751JN108-4
Data sheet
- Product group
- Safety equipment
- Main category
- Sign and lock
- Sub category
- Cones and barricade tapes
- Name of the product
- Warning tape
- Product code
- ECT751JN108
- Sort by keywords
- Hazard tapes
- Product use
- Marking physical hazards
- Approved/Certified
- Complies with ANSI Z535.1 color standards, according to the manufacturer
- Manufacturer
- Incom Direct
- Country of origin
- Taiwan
- Thickness in mils
- 6.3 mils
- Elongation at break (%)
- 180 %
- Features
- Smooth gloss finish, easily cleaned
- Additional Features
- Abrasion resistance
- Tensile strength (kg/cm ; lb/in)
- 3.1 kg/cm ; 17.6 lb/in
- Includes
- 1 roll
- Includes 2
- Clear protective film
- Operating temperature
- Below 140°F / 60°C
- Shelf life
- One year after shipment, at moderate temperature and humidity
- Mounting type
- Pressure-sensitive rubber-based adhesive
- Adhesion to steel (kg/cm ; oz/in)
- 0.20 kg/cm ; 17.64 oz/in
- Material
- Soft PVC
- Length (ft/m)
- 108 ft / 32.92 m
- Dimensions of the product
- The dimensions of the product depend on the size selected by the customer
- Length (in/cm)
- 5 in / 12.7 cm
- Width (in/cm)
- 5 in / 12.7 cm
- Height (in/cm)
- 4 in / 10.16 cm
- Weight (lb/kg)
- 1.68 lb / 0.762 kg
- ***Size and weight according to selection***
- Based on the ECT751JN108-4
- Availability
- 2 and 3 in widths ship quickly; allow 5 days for other widths
- Sold by
- Roll
- Color
- Yellow/Black
- HS Code
- 3919102055
- Return conditions
- Not returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page
- Caution
- Apply to a clean, dry and smooth floor
Specific References
- mpn
- LWT420
You might also like
Comments (0)
No customer reviews for the moment.
8 other products in the same category:
Laminated yellow and black hazard tape sold in a 108 ft roll, for continuous marking of traffic lanes and long workshop or warehouse runs, and for marking physical hazards on floors, walls, pipes and equipment. Choose a width of 1, 2, 3, 4 or 6 in from the menu; the length stays fixed. Made of 6.3 mils soft PVC under a clear protective film, it has a smooth gloss finish and a pressure-sensitive rubber-based adhesive.