compare_arrows

Laminated PVC hazard tape, yellow/black, 54 ft, 1 to 6 in

Reference : ECT751JN54-1
$7.40

To mark around equipment, define an area or identify a workstation, this 54 ft roll of laminated yellow and black tape suits one-off jobs. Select a width of 1, 2, 3 or 6 in from the menu; the length does not change. The 6.3 mils soft PVC, protected by a clear film, has a smooth gloss finish. Its pressure-sensitive rubber-based adhesive goes on a clean, dry and smooth surface, whether a floor, a wall or a pipe.

Width: 1 in
Quantity

Compare

Laminated PVC hazard tape, yellow/black, 54 ft, 1 to 6 in

A 54 ft roll for localized marking around equipment and workstations.

Choose the width that suits your marking job from the available formats.

Format Sylprotec code Best used for
1 in X 54 ft ECT751JN54-1 Bundling and pipe identification
2 in X 54 ft ECT751JN54-2 Identifying equipment or a workstation
3 in X 54 ft ECT751JN54-3 Outlining a machine or a small area
6 in X 54 ft ECT751JN54-6 Wide band to mark one specific physical hazard

Around equipment, an area or a workstation, this yellow and black tape makes a physical hazard or a boundary easier to spot. Its 54 ft length is meant for localized marking and one-off jobs, on a floor, a wall, a pipe or the equipment itself. It is made of 6.3 mils soft PVC under a clear protective film, with a pressure-sensitive rubber-based adhesive. The manufacturer states that its colors follow the ANSI Z535.1 color code.

Features of the 54 ft laminated hazard tape

  • 54 ft length suited to localized marking.
  • Several widths to suit the area being marked.
  • Clear protective film over soft PVC.
  • Smooth gloss finish, easily cleaned.
  • Abrasion resistance.
  • Pressure application, with no adhesive to add.

Applications of the 54 ft laminated hazard tape

Use it to surround the base of a machine, mark a workstation, identify equipment or pick out a pipe. It also serves for color coding and bundling, two uses the manufacturer lists for this series. During a one-off rearrangement, this 54 ft format lets you mark the spot in question without planning a long run.

For a narrow marker on a pipe or small equipment, the 1 in or 2 in is enough. The 3 in width outlines a machine or workstation more clearly. The 6 in suits a physical hazard that must stand out over a short distance. This tape is not anti-slip: its finish stays smooth.

Technical specifications of the 54 ft laminated hazard tape

Characteristic Detail
Material Soft PVC
Protective film Clear
Adhesive Rubber-based, pressure-sensitive
Finish Smooth gloss, easily cleaned
Color Yellow/Black
Tape thickness 6.3 mils (0.160 mm)
Roll dimensions For the 4 in X 54 ft roll: height 4 in / 10.16 cm (tape width); estimated diameter 5 in / 12.7 cm, roll laid flat
Weight For the 4 in X 54 ft roll: 1 lb / 0.45 kg
Service temperature Below 60 °C / 140 °F
Adhesion to steel (typical value) 0.20 kg/cm; 17.64 oz/in
Elongation at break (typical value) 180 %
Tensile strength (typical value) 3.1 kg/cm; 17.6 lb/in, values as published
Storage One year from dispatch, at moderate temperature and humidity
Country of origin Taiwan
Sold by Roll

The 5 in diameter of the 4 in X 54 ft roll is a cautious estimate, made by comparison with the 4 in X 108 ft roll from the same range: it has not been measured on this format. Typical values are averages obtained by the ASTM D-1000 test method; they give an order of magnitude and do not indicate any allowable load.

Care and application of the 54 ft laminated hazard tape

Around a workstation or equipment, first remove contaminants from the target area, then make sure the surface is clean, dry and smooth. Test the tape on that surface, then press it firmly into place. Its smooth finish makes cleaning easier. Keep it away from temperatures of 60 °C / 140 °F and above, and store the rest of the roll at moderate temperature and humidity.

FAQ: the 54 ft laminated hazard tape

Which width should I use to mark around a machine?

The 3 in width draws a clearly legible outline. For a simple marker on equipment, the 1 in or 2 in is enough, and the 6 in makes a physical hazard stand out over a short distance.

Is this tape anti-slip?

No. Its clear protective film gives it a smooth gloss finish. Where foot traction is the concern, choose an anti-slip tape instead, offered in the suggestions below.

How should I prepare the surface before applying it?

Remove contaminants and check that the surface is clean, dry and smooth. A test on a short piece confirms adhesion; then press the tape firmly into place.

At what temperature can this tape be used?

Its published service limit is below 60 °C / 140 °F. Keep this in mind near equipment that gives off heat.

What jobs suit the 54 ft length?

The 54 ft roll suits localized marking: outlining equipment, identifying a workstation or marking a pipe. Choose the width according to the area being marked.

Suggestions for the 54 ft laminated hazard tape

When the job takes place at the foot of a machine or around a workstation, the person doing it can count on the Solus safety glasses (YAS1101) with clear anti-fog lenses, the high-quality cowhide and cotton knit gloves (G300) with tough cuffs, the Impacto kneepads (VG102) for floor work and the adjustable fluorescent orange safety vest (VV50) with 4 pockets if vehicles pass nearby. The Delta Plus Independence safety helmet (TA14LR) is added when the area requires head protection.

Three useful additions for this localized marking job are: 28 in orange cone with two reflective bands (EPTCONE28B), yellow and black expandable polypropylene barrier (EPT195) and automatic retracting safety knife (SAEC5). Select them according to the layout and hazards present.

The texts coloured in green correspond to hyperlinks leading to specific safety equipment or to a general information link.

ECT751JN54-1

Data sheet

Product group
Safety equipment
Main category
Sign and lock
Sub category
Cones and barricade tapes
Name of the product
Warning tape
Product code
ECT751JN54
Sort by keywords
Hazard tapes
Product use
Marking physical hazards
Approved/Certified
Complies with ANSI Z535.1 color standards, according to the manufacturer
Manufacturer
Incom Direct
Country of origin
Taiwan
Thickness in mils
6.3 mils
Elongation at break (%)
180 %
Features
Smooth gloss finish, easily cleaned
Additional Features
Abrasion resistance
Tensile strength (kg/cm ; lb/in)
3.1 kg/cm ; 17.6 lb/in
Includes
1 roll
Includes 2
Clear protective film
Operating temperature
Below 140°F / 60°C
Shelf life
One year after shipment, at moderate temperature and humidity
Mounting type
Pressure-sensitive rubber-based adhesive
Adhesion to steel (kg/cm ; oz/in)
0.20 kg/cm ; 17.64 oz/in
Material
Soft PVC
Length (ft/m)
54 ft / 16.46 m
Length (in/cm)
5 in / 12.7 cm
Width (in/cm)
5 in / 12.7 cm
Height (in/cm)
4 in / 10.16 cm
Weight (lb/kg)
1 lb / 0.45 kg
***Size and weight according to selection***
Based on the ECT751JN54-4
Availability
Allow 5 days for delivery
Sold by
Roll
Color
Yellow/Black
HS Code
3919102055
Return conditions
Not returnable if used. For more information about our return policy, please refer to the "Orders and Returns" link on the home page
Caution
Apply to a clean, dry and smooth floor

Specific References

MPN
LWT110

You might also like

Comments (0)
No customer reviews for the moment.