- New
This item is not kept in stock. Please allow 5 days for delivery.
Tape with black and photoluminescent stripes to mark off hazard areas and mark steps, handrails and exit routes, available in 30 ft rolls in a 2, 4 or 6 in width. It recharges with ambient light, with no electricity, and the manufacturer states 6 hours or more of glow. Its permanent pressure-sensitive adhesive holds on clean, dry indoor surfaces.
This item is not kept in stock. Please allow 5 days for delivery.
Available widths: 2 in, 4 in and 6 in, 30 ft roll
Available in 3 widths. Select the variant you need from the drop-down menu.
| Sylprotec code | Width | Length | Weight |
|---|---|---|---|
| ECTNOPH-2 | 2 in (5.08 cm) | 30 ft (9.14 m) | 0.5 lb (0.23 kg) |
| ECTNOPH-4 | 4 in (10.16 cm) | 30 ft (9.14 m) | 1 lb (0.45 kg) |
| ECTNOPH-6 | 6 in (15.24 cm) | 30 ft (9.14 m) | 1.5 lb (0.68 kg) |
The dimensions shown are for variant ECTNOPH-2.
This tape with black and photoluminescent stripes marks off hazard areas and critical spots when the lighting fails: step edges, handrails, door frames, exit routes and the surroundings of safety equipment. The black bands keep the contrast by day and in dim light. Its photoluminescent bands absorb ambient light during normal lighting hours, then release it as a glow in the dark, with no electricity: the manufacturer states 6 hours or more of luminance. Its permanent pressure-sensitive adhesive holds on clean, dry indoor surfaces. It complements emergency lighting and exit signage, without replacing them. The 30 ft (9.14 m) roll comes in a 2 in (5.08 cm), 4 in (10.16 cm) or 6 in (15.24 cm) width. It is made in the United States.
The manufacturer recommends it for hazard striping, emergency exit routes and stairwells, marking handrails, door frames and safety equipment, and evacuation markers in the event of a total lighting failure. The 2 in width suits steps and handrails, the 4 in width stays clearly visible on walls and around hazard areas, and the 6 in width, the most visible, suits walls and large areas. Important: check with local, provincial and federal authorities that this product is suitable for your use in an evacuation route or emergency exit. This page carries black stripes only. The same widths come in red stripes on the sister page, the striped photoluminescent roll (ECTRGPH), red, 30 ft. For a continuous, fully photoluminescent marker, choose the plain photoluminescent tape (ECTPH), 30 ft instead, a separate construction.
| Feature | Detail |
|---|---|
| Colour | Black stripes alternating with photoluminescent bands |
| Type | Striped photoluminescent tape |
| Material | Vinyl |
| Luminance | 6 hours or more in the dark after charging with ambient light |
| Widths | 2 in (5.08 cm), 4 in (10.16 cm) or 6 in (15.24 cm) |
| Length | 30 ft (9.14 m) per roll |
| Adhesive | Permanent, pressure-sensitive |
| Application surface | Clean and dry, indoors |
| Standards cited by the manufacturer and its distributors | DIN 67510, ASTM E2072-14, ISO 15370, EU Marine Equipment Directive, IMO Resolution A.752(18), PSPA Class B |
| Country of origin | United States |
| Sold by | Roll |
Clean the surface and let it dry: the permanent adhesive requires a clean, dry substrate. Unroll the tape, cut it to length and press it firmly across its full width. Apply it where it receives ambient light during normal lighting hours, since that light recharges it. Keep its surface clean so it keeps charging and glowing, and replace any damaged section.
The 2 in suits steps and handrails. The 4 in stays clearly visible on walls and around hazard areas. The 6 in, the most visible, suits walls and large areas.
The manufacturer states a visible glow for 6 hours or more in the dark, after charging with ambient light.
The plain tape is fully photoluminescent and lays out a continuous marker; the striped tape alternates photoluminescent bands and coloured bands to signal a hazard. They are two separate constructions: the standards cited for the plain version are not certifications of this striped tape.
No. It complements emergency lighting and exit signage by marking hazards and routes. Check with local, provincial and federal authorities that the product is suitable for each use in an evacuation route or emergency exit.
The manufacturer presents it as an indoor marking solution. Apply it to clean, dry indoor surfaces.
For the technician who applies the stripes to the steps of a service stairway, plan for the Impacto (VG104) soft rubber knee pads with foam, the TenActiv (GS21TXUGFN) high-visibility ultra-thin cut-resistant gloves, the 3M (YASF401BG) SecureFit 400 series safety glasses with clear anti-fog lens, the MSA V-Gard (TA83-W) matte white helmet, type 1 class E and the 3M 1100 (O1100) uncorded disposable earplugs.
To complement your equipment: Photoluminescent Running Man exit sign with 90 degree right arrow (EI313PH); Photoluminescent Running Man exit sign with down arrow (EI309PH) and Green Running Man LED emergency exit sign, thermoplastic casing, with back-up battery (LUMR).
Data sheet
Specific References
You might also like