Kleton tubular perimeter guard 8 ft, safety yellow

Kleton tubular perimeter guard 8 ft, safety yellow

Manufacturer code Kleton: KD134, model KD134

This item is not kept in stock. Please allow 15 days for delivery.

Available in 2 sizes. Select the variant you need from the drop-down menu.

The 8 ft Kleton tubular perimeter guard covers a long run with fewer sections. Made of 2 in square tube in safety yellow, it is 49-1/2 in high and its posts stand on 5/16 in base plates drilled for floor anchoring. The line starts with a 96 in starter section; it is extended with 94 in add-on sections attached one after the other, and the hardware used to attach the add-on sections is included. An add-on section cannot be installed on its own: it requires a starter section. Floor anchors (2 per post) and post caps (1 per post) are sold separately. Made in Canada, the guard is covered by a 1-year limited warranty.

Features of the Kleton 8 ft perimeter guard

• 8 ft sections: 96 in starter or 94 in add-on
• 2 in square tube, safety yellow, 49-1/2 in high
• Posts with 5/16 in base plate drilled for floor anchoring
• Add-on section attached to a starter section (cannot be installed on its own)
• Add-on section hardware included; anchors and caps sold separately

Applications of the Kleton 8 ft perimeter guard

Anchored to the floor along a long wall, a receiving area or a pedestrian aisle in a plant or warehouse, the 8 ft guard physically marks off an area over a long span. The 96 and 94 in sections weigh 66 and 53 lb: plan their handling accordingly. For shorter spans, the same guard comes in 4 ft on a separate page.

Care of the Kleton 8 ft perimeter guard

Clean with soapy water. Periodically check that the floor anchors and the hardware between sections are tight. Replace any section that is bent after an impact and put a cap back on any post that has lost it.

FAQ: the Kleton 8 ft perimeter guard

Can I install a 94 in add-on section on its own?

No. It attaches after a 96 in starter section: every line starts with a starter section.

Are floor anchors and caps included?

No. Plan for 2 floor anchors and 1 cap per post, sold separately. Only the hardware that attaches the add-on sections is included.

How much does each section weigh?

The 96 in starter section weighs 66 lb and the 94 in add-on section weighs 53 lb.

Is a shorter version available?

Yes. The same tubular guard is offered in 4 ft (48 in starter section and 46 in add-on section) on a separate page.

Where is the guard made and what is the warranty?

It is made in Canada and covered by a 1-year limited warranty.

Suggestions for this Kleton 8 ft perimeter guard

For the dock foreman having this 8 ft Kleton guard installed along the receiving area, plan for a Pioneer yellow surveyor vest (V6693) with 16 pockets to keep anchors and tools within reach, TenActiv foam nitrile gloves (GS21TXUFNLTC) reinforced with leather between thumb and index finger to carry the long sections, Uvex Genesis espresso anti-fog safety glasses (YAU3201) near sunny dock doors, Laser Lite uncorded disposable earplugs (OA1101) while drilling and a 3M 9211 valved mask (R9211) against concrete dust.

During installation, close off the area with a red “Danger” barricade tape (ECT3RE9) and a large 36 in orange cone (EPTCONE36) with reflective bands. For a shorter span, see the same guard in its 4 ft size (EBKD132); along a wall, see the Kleton 48 or 60 in floor angle (EBRN065-48) guard and the same guard rail in a 120 in length (EBRN065-120).

The texts coloured in green correspond to hyperlinks leading to specific safety equipment or to a general information link.