Kleton tubular perimeter guard 4 ft, safety yellow

Kleton tubular perimeter guard 4 ft, safety yellow

Manufacturer code Kleton: KD132, model KD132

This item is not kept in stock. Please allow 15 days for delivery.

Available in 2 sizes. Select the variant you need from the drop-down menu.

The Kleton tubular perimeter guard forms a 49-1/2 in high barrier made of 2 in square tube, in safety yellow. Its posts stand on 5/16 in base plates drilled for floor anchoring. The line starts with a 48 in wide starter section; it is then extended with 46 in add-on sections attached one after the other, and the hardware used to attach the add-on sections is included. An add-on section cannot be installed on its own: it requires a starter section. Floor anchors (2 per post) and post caps (1 per post) are sold separately. Made in Canada, the guard is covered by a 1-year limited warranty.

Features of the Kleton perimeter guard

• 2 in square tube, safety yellow
• 49-1/2 in overall height
• Posts with 5/16 in base plate drilled for floor anchoring
• 48 in starter section or 46 in add-on section (add-on requires a starter section)
• Add-on section hardware included; anchors and caps sold separately

Applications of the Kleton perimeter guard

Anchored to the floor in a plant or a warehouse, the Kleton tubular perimeter guard physically marks off an area: around equipment, a work area or along a pedestrian aisle. Start with a starter section, then add as many 46 in add-on sections as needed to cover the required length. For longer spans, the same guard comes in 8 ft on a separate page.

Care of the Kleton perimeter guard

Clean with soapy water. Periodically check that the floor anchors and the hardware between sections are tight. Replace any section that is bent after an impact and put a cap back on any post that has lost it.

FAQ: the Kleton perimeter guard

Can I install an add-on section on its own?

No. The 46 in add-on section attaches after a starter section: always start the line with a 48 in starter section.

Are floor anchors and caps included?

No. Plan for 2 floor anchors and 1 cap per post, sold separately. Only the hardware that attaches the add-on sections is included.

How much does each section weigh?

The 48 in starter section weighs 45 lb and the 46 in add-on section weighs 32 lb.

Is a longer version available?

Yes. The same tubular guard is offered in 8 ft (96 in starter section and 94 in add-on section) on a separate page.

Where is the guard made and what is the warranty?

It is made in Canada and covered by a 1-year limited warranty.

Suggestions for this Kleton perimeter guard

For the warehouse manager having this Kleton guard anchored along a pedestrian aisle, plan for a fluorescent yellow traffic vest (VV53J-4XL5XL) with four pockets to stay visible to forklift drivers, Dexterity Kevlar gloves (GS18KGFN) with foam nitrile coating, touchscreen compatible, to handle the sections, Uvex Genesis anti-fog safety glasses (YAU3200) against concrete chips when drilling, a 3M Optime 95 earmuff (OPH6A) against hammer drill noise and a 3M 8511 mask (R8511) with Cool Flow valve against concrete dust.

During installation, mark off the work area with a yellow “Danger” barricade tape (ECT3YE7) and an 18 in orange traffic cone (EPTCONE). For a longer line, see the same guard in its 8 ft version (EBKD134); to protect a machine or a door, the Kleton low-profile guard (EBKD127), and along a wall, the Kleton floor angle rail (EBRN065-48).

The texts coloured in green correspond to hyperlinks leading to specific safety equipment or to a general information link.