- New
The 3M 7990 clip-on welding shield kit attaches without tools to the 3M 7800S series reusable full facepiece (R7800) to weld with the same respiratory protection. According to the 3M instructions, it includes the welding shield, the cover plate and the 7992 lens gasket, and accepts standard 4.5 in x 5.25 in passive lenses. The shaded lens and the 7800S facepiece are not included; choose the shade suited to your process following the 3M instructions.
Delivery time: 7 business days.
3M manufacturer code: 7000126524, model 7990
The 3M 7990 clip-on welding shield kit turns the 3M 7800S series reusable full facepiece into a welding facepiece: the shield clips onto the facepiece lens frame, without tools. According to the 3M instructions, the kit includes the welding shield, the cover plate and the 7992 lens gasket; it accepts standard 4.5 in (114.3 mm) x 5.25 in (133.4 mm) passive welding lenses, to be chosen according to the process. The lens holder flips up to inspect the work. The 7800S facepiece and the shaded lens are not included.
When a respiratory full facepiece is required during welding, the 7990 kit lets crews keep the 7800S and add a welding shield to it, without changing respirators. The shield clips onto the lens frame without tools, and its lens holder flips up to inspect the workpiece.
It accepts standard passive lenses, chosen according to the process, or the 7991 electronic lens assembly.
The kit attaches to the 3M 7800S series reusable full facepiece (R7800). It accepts standard 4.5 in (114.3 mm) x 5.25 in (133.4 mm) passive lenses and the 3M 7991 electronic lens assembly, sold separately. To cover the head and shoulders, the instructions list the leather shroud (R7993) as an accessory.
The kit is intended for welders who must wear a respiratory full facepiece while welding, for example in the marine sector, shipbuilding and repair, bridges, petroleum refineries, primary metals and fabricated metal products, according to the 3M specification sheet. It lets crews standardize respiratory protection on the 7800S, approved by 3M for several air supply modes, while adding the welding shield.
| Component | 3M model | Status |
|---|---|---|
| Clip-on welding shield | 7990 | Included |
| Cover plate | Included | |
| Lens gasket | 7992 | Included |
| Reusable full facepiece | 7800S | Sold separately |
| Electronic lens assembly | 7991 | Sold separately |
Welding filter sold separately: the shaded lens is not included.
First insert the cover plate, the 7992 gasket and the shaded passive lens under the lens holder retaining clips, in the order shown in the instructions. Then align the 7990 shield on the 7800S facepiece, attach its lower lip to the bottom of the lens frame and rotate the top until the tabs snap behind the frame. Before welding, check the full facepiece seal according to its instructions and that the shield is held firmly.
The shield helps protect the eyes and face against visible, ultraviolet and infrared radiation, sparks and spatter, but 3M specifies that it provides limited protection and does not constitute primary eye protection. Choose the lens shade suited to your work, following the selection guidance in the 3M instructions. The shield does not filter air: respiratory approval remains that of the 7800S facepiece and its configuration. Only people trained in its use and maintenance should use it.
Inspect the kit before each use and replace any damaged or defective part before welding. Clean the shield with mild soap and water, without solvents. Change the cover plate as soon as it is pitted or cloudy, and the 7992 lens gasket if it is cracked or distorted.
The 3M 7800S series reusable full facepiece, by clips on the facepiece lens frame.
The welding shield, the cover plate and the 7992 lens gasket. The 7800S full facepiece is not included.
No. Choose a standard 4.5 in (114.3 mm) x 5.25 in (133.4 mm) passive lens, with the shade suited to your process according to the 3M instructions, or the 3M 7991 electronic lens assembly, sold separately.
No. 3M specifies that it helps protect the eyes and face, with limited protection, but does not constitute primary eye protection.
Clean it with mild soap and water, without solvents. Inspect the kit before each use: change the cover plate if it is pitted or cloudy and the 7992 gasket if it is cracked or distorted.
Under the full facepiece, the welder wears the orange Pioneer 7743 FR-Tech flame-resistant shirt (V130) and the Pioneer 7764 flame-resistant cargo pants (V7764) with high-visibility stripes. The 11 in leather welding gloves (G605) protect the hands, the 29 dB Classic (OA101) disposable earplugs reduce noise, and the 6.5 in leather gaiters (VCSPL4) resist heat.
This kit mounts on the 3M 7800 series full respirator (R7800). The 7093 P100 filters (R7093) address particles in certain welding fumes, not gases or vapours; their selection requires an approved configuration, a contaminant assessment and a fit test. The 3M 504 cleaning wipes (R504) provide maintenance for the facepiece.
Data sheet
Specific References
You might also like