The 3M Adflo 35-1099-01 motor blower is the replacement blower unit of the Adflo powered air purifying respirator, supplied with its cover. It draws air through the filter and delivers it to the helmet with automatic airflow regulation, with low airflow and low battery alarms. With no serviceable parts, it replaces a damaged blower. Plan for the 35-1099-07 lithium-ion battery (R35-1099-07), charger, belt, HE filter and breathing tube, sold separately.
Delivery time: varies; contact us.
3M manufacturer code: 7100200559, model 35-1099-01
The 3M Adflo 35-1099-01 motor blower is the replacement blower unit of the Adflo powered air purifying respirator, supplied with its cover. It is the heart of the unit: it draws ambient air through the filter and delivers it to the welding helmet through the breathing tube, automatically regulating airflow according to battery charge and filter loading. 3M states that the blower contains no serviceable parts; replacing it puts back into service an Adflo whose motor or housing is damaged. The battery, charger, belt, breathing tube and headtop are ordered separately.
The blower contains no serviceable parts: when the motor or housing of an Adflo is damaged, it is replaced. The 35-1099-01 puts the unit back into service while keeping the battery, charger, belt and breathing tube already in place, without buying a complete PAPR assembly again.
It keeps the Adflo blower functions: airflow regulated automatically according to battery charge and filter loading, audible and visual low airflow and low battery alarms.
The 35-1099-01 is the replacement blower of the Adflo powered air purifying respirator. It runs on the 35-1099-07 Adflo lithium-ion pack (R35-1099-07), is worn on the Adflo waistbelt (R15-0099-16) and connects to an approved headtop through a breathing tube listed on the Adflo NIOSH label. It does not replace the complete PAPR assembly, which includes other parts.
This blower is intended for Adflo users and fleet maintenance staff in design and construction, heavy infrastructure and industrial maintenance. 3M specifies it for welding, machine operation, facility maintenance, sanding, assembly and grinding. A spare blower allows a unit out of service to be replaced quickly without buying the complete assembly again.
| Component | 3M model | Status |
|---|---|---|
| Adflo motor blower with cover | 35-1099-01 | Included (quantity: 1) |
| Adflo lithium-ion battery | 35-1099-07 | Sold separately |
| Adflo smart charger | 35-0099-08 | Sold separately |
| Belt, breathing tube, HE filter and headtop | Sold separately |
Hook the left edge of the battery into its holder at the bottom of the blower and push until the two clicks. Place the spark arrestor, prefilter and HE filter in the filter cover, lock it, then attach the blower to the belt with the hook-and-loop straps, with the UP arrow pointing up. Insert the breathing tube approved for your headtop and turn it a quarter turn.
Before entering the work area, turn the blower on, let it run for 2 minutes and check airflow with the 15-0099-05 flow indicator (R15-0099-05); then block the tube: the low airflow alarm must trigger after 15 to 30 seconds. Use is part of the employer's respiratory protection program, with headtop selection, training and fitting.
The blower is part of a NIOSH-approved Adflo system and protects only in a complete approved configuration. Do not use it in an oxygen-deficient atmosphere (less than 19.5%), at unknown concentrations, in conditions immediately dangerous to life or health, or in a flammable or explosive atmosphere. Leave the area as soon as an alarm is triggered; the blower stops 2 minutes after a continuous low airflow alarm. Operating range: -5 °C (23 °F) to 55 °C (131 °F).
Never attempt to open the blower to repair it. After each use, remove the battery, breathing tube and headtop, then clean the outside surfaces with a soft cloth dampened with water and neutral pH mild detergent, without solvents or immersion; do not use compressed air or a vacuum inside. Dust in the blower may signal a filter leak: check it before the next use. Store the unit between -20 °C (-4 °F) and 35 °C (95 °F), away from sunlight, at a relative humidity of 90% or less and without condensation; short-term storage, non-operating and under 1 month, is permitted up to 55 °C (131 °F).
The Adflo motor blower with its cover, and no other part.
No. The 35-1099-07 Adflo lithium-ion battery and the 35-0099-08 smart charger are ordered separately, as are the belt, breathing tube and headtop.
No. It is a replacement component. NIOSH approval applies to the complete approved Adflo configuration, with the specified filter, battery, breathing tube and headtop, never to the motor alone.
Remove the battery, breathing tube and headtop, then wipe the outside with a soft cloth dampened with water and neutral pH mild detergent. Do not immerse it, do not use solvents and do not blow compressed air inside.
No. 3M states that the blower contains no serviceable parts and must never be opened: a damaged blower is replaced.
Under the helmet connected to the Adflo, a Nomex hood (V309) and clear Ultra-Spec 2001 OTG safety glasses (YAU0112) protect the welder's head and eyes; clear Cee-Tec (YA12E93101DX) glasses with foam seal are another option. The 11 in leather welding gloves (G605) cover the hands, and the 3M 1100 disposable earplugs (O1100) reduce noise.
The blower runs on the 35-1099-07 Adflo lithium-ion accumulator (R35-1099-07), to be recharged only on the 35-0099-08 smart charger (R35-0099-08), and is worn on the 15-0099-16 leather belt (R15-0099-16). It takes the Adflo high-efficiency filters (R15-0299-2) and connects to the helmet through the SG-30W self-adjusting breathing (RSG-30W) tube, whose 15-0099-12 O-ring seal (R15-0099-12) ensures tightness.
Data sheet
Specific References
You might also like