The 3M Adflo PAPR assembly supplies filtered air to welders wearing a Speedglas helmet with respiratory protection. It is offered belt-mounted or on the back on the BPK-HD backpack; for the backpack format, 3M lists the blower, a lithium-ion battery, a high-efficiency filter and a charger. Automatically regulated airflow, with low airflow and low battery alarms. Plan for the headtop and an approved Speedglas (RSG-50W) tube, such as the SG-50W for M-400 headtops.
Delivery time: varies; contact us.
3M manufacturer code: listed for each format in the format table below
Available in 2 formats, belt-mounted or worn on the back with a backpack; choose yours in the format table below.
| Format | Sylprotec code | Manufacturer model | Manufacturer product number |
|---|---|---|---|
| Belt-mounted | R35-5401-01-CEINT | 7100260610 | |
| BPK backpack | R35-5401-01-DOS | 35-5401-BPK | 7100349640 |
The 3M Adflo PAPR assembly is the powered air purifying respirator designed for welders, with a lithium-ion battery. It is offered in two formats: the belt-mounted assembly and the back-worn assembly on the BPK-HD heavy-duty backpack, which keeps the unit flat against the back and leaves the waist free; the Adflo instructions state that the BPK-HD can be used in place of the belt. For the backpack format, 3M lists the Adflo blower, a lithium-ion battery, a high-efficiency filter and a charger in the contents. Connected through an approved breathing tube to a Speedglas welding helmet with respiratory protection, the Adflo delivers filtered air at more than 170 l/min, regulated automatically according to battery charge and filter loading. The headtop and breathing tube are chosen separately.
The Adflo PAPR assembly groups the power supply, filtration and recharging of the powered air purifying respirator designed for welders: PAPR unit, lithium-ion battery, high-efficiency filter and charger. Airflow, greater than 170 l/min, is regulated automatically according to battery charge and filter loading, with audible and visual low airflow and low battery alarms.
Two carrying configurations are offered: on the belt, or on the back on the BPK-HD backpack, which leaves the waist free for work bent over or in tight spaces.
The Adflo is used with Speedglas welding helmets with respiratory protection and approved 3M headtops, according to its NIOSH approval label. The Adflo (RSG-50W) tube must be approved for the headtop: with an M-400 headtop, the SG-50W tube is mandatory. The BPK-HD backpack of the backpack format adjusts for a chest circumference of 75 cm (29.5 in) to 130 cm (51 in), weighs 415 g (0.9 lb) and 3M declares it flame resistant according to ISO 16321-1 §7.8.
This assembly is intended for welders exposed to welding fumes and particles in industrial maintenance, design and construction and heavy infrastructure projects. 3M recommends it for welding, grinding, sanding, assembly, machine operation and facility maintenance. The backpack format suits work in tight spaces, bent over or on the ground, where a belt gets in the way. With the optional organic vapour and acid gas cartridge, it also covers certain gases, in an approved configuration and according to the risk assessment.
| Component | Belt-worn | Back-worn (BPK) |
|---|---|---|
| Adflo PAPR unit | Included | Included |
| Lithium-ion battery | Included | Included |
| High-efficiency filter | Included | Included |
| Charger | Included | Included |
| Carrying mode | On the belt | BPK-HD backpack, in place of the belt |
| Headtop and breathing tube | Not included | Not included |
Additional contents depend on the chosen configuration. The back plate belongs to the backpack of the backpack format; it is not a material of the PAPR unit. The gas cartridge and nuisance odour pad are available as options.
Charge the battery on receipt with the Adflo charger. Place the spark arrestor, prefilter and HE filter in the filter cover, then lock it onto the blower. Choose a breathing tube approved for your headtop on the Adflo NIOSH label, insert its two pins into the air outlet and turn a quarter turn. Wear the unit on the belt or on the BPK-HD backpack depending on the format.
Before entering the work area, check the airflow with the flow indicator and that the low airflow alarm triggers. The Adflo is used as part of the employer's respiratory protection program: risk assessment, headtop selection, training and fitting.
The PAPR unit alone has no standalone protection factor: the protection factor is determined by the complete approved configuration, with the specified headtop and breathing tube. The HE filter captures particles; it does not protect against gases or vapours and does not supply oxygen. Do not use the Adflo in an oxygen-deficient atmosphere (less than 19.5%), at unknown concentrations, in conditions immediately dangerous to life or health, or in a flammable or explosive atmosphere. Leave the area immediately if an alarm is triggered. Between 5000 feet and 10,000 feet of altitude, use only the HE filter, without cartridge or odour pad. Operating range: -5 °C (23 °F) to 55 °C (131 °F).
| Specification | Detail |
|---|---|
| Product type | Powered air purifying respirator assembly |
| Product series | Adflo |
| Formats | Belt-mounted ; backpack on BPK-HD |
| Displayed dimensions and weight | Belt format (R35-5401-01-CEINT): height 8.6 in / 21.84 cm; length 13.8 in / 35.05 cm; width 7.8 in / 19.81 cm; weight 5.315 lb / 2.4 kg |
| Filter included | High-efficiency filter (NIOSH colour code magenta) |
| Battery type | Lithium-ion |
| Run time | Up to 12 hours, with a new charged battery and a new HE filter |
| Airflow | Greater than 170 l/min (6 cfm) |
| Noise level | Less than 80 dBA at the wearer's ear |
| Protection factor | Determined by the complete approved configuration |
| Storage temperature | -20 °C (-4 °F) to 35 °C (95 °F), relative humidity 90% or less, non-condensing; up to 55 °C (131 °F) for short-term, non-operating storage under 1 month |
| Intrinsically safe | No |
| Approval | NIOSH approved in the approved Adflo configuration |
| Recommended industries | Industrial maintenance ; Design and construction ; Heavy infrastructure |
| Recommended applications | Assembly ; Facility maintenance ; Grinding ; Machine operation ; Sanding ; Welding |
Charge the battery on receipt, only with the 35-0099-08 Adflo charger, indoors and in a ventilated area; it reaches 80% in about 3 hours and 100% in about 6.5 hours. Before each use, inspect the filter and its gasket, the prefilter, the spark arrestor and the breathing tube, then check the airflow with the flow indicator and the low airflow alarm. After use, clean the blower and battery with a soft cloth dampened with water and mild detergent, without solvents or immersion. The filter and prefilter cannot be cleaned: replace them if they are damaged, wet or loaded. Store the assembly between -20 °C (-4 °F) and 35 °C (95 °F), away from sunlight, at a relative humidity of 90% or less and without condensation; short-term storage, non-operating and under 1 month, is permitted up to 55 °C (131 °F).
The belt format keeps the PAPR at the waist. The BPK backpack format carries it flat against the back on the BPK-HD heavy-duty backpack, which replaces the belt and leaves the waist free; it suits work bent over, on the ground or in tight spaces.
No. The headtop and breathing tube are chosen separately, among the models approved on the Adflo NIOSH label.
Both formats include the Adflo PAPR, a lithium-ion battery, a high-efficiency filter and a charger. The backpack format adds the BPK-HD backpack, which replaces the belt; additional contents depend on the chosen configuration.
No. The HE filter protects against particles. For certain organic vapours and acid gases, the optional Adflo cartridge must be added, always with the HE filter, prefilter and spark arrestor, according to the SDS and the risk assessment.
Check the battery charge and the condition of the filter and its gasket, the prefilter, the spark arrestor and the breathing tube, then check the airflow with the flow indicator and that the low airflow alarm triggers before entering the work area.
Under the helmet connected to the Adflo, the welder keeps clear Virtua Max safety glasses (YA11329), Milwaukee Performance (YA8732040) anti-fog glasses or clear Virtua (YA11872) Max 11872 glasses with foam gasket. The 12 in side-split leather welding gloves (G601) cover the hands, and the Optime 105 behind-the-head H10B earmuff (OPH10B) is worn with the helmet in noisy shops.
To complete the system, the Versaflo (RM407SG) M-407SG helmet assembly with Speedglas 9100 welding shield connects through the SG-50W noise-reducing breathing (RSG-50W) tube, which 3M requires with M-400 headtops, and the SG-15 flame-resistant sleeve (RSG15) protects the tube from sparks. For certain gases, add the 15-0499 organic vapour and acid gas cartridges (R15/0499-2), or the 35-0699 nuisance odour pad assembly (R35-0699). The 6-position charging stand (R35-0099-08N6) recharges the batteries of a whole crew.
Data sheet
Specific References
You might also like